Well girls, this is the end result of all the effort we have done you, and I Susi since May, do you seem to have been worth it? we think so. 
To paint your picture!
Materials:
-2 cans of spray paint selected color, and long lasting color richer than does not peel, buy a can of paint says waterproof = $ 12
- package steel wool (the color should be silver, no bronze or gold) = $ 3
-A package of coarse sand paper (the half material so it's not too rough) = $ 5
-2 cans of clearcoat = $ 12
Tin -1 primer! - $ 5
-X2 clothes hangers metal - In your basement, or ask his mother for free = $ 0
Total: $ 37 USD
Step 1: Strip your bike to anything! Remove all parties, all you want if the frame naked!
Step 2: the fork and headset)! Place a rag in his insterrior tube (in which a put option and put a rag in your bottom bracket and the interior, where you can put your seatpost inches
Step 3: Tape adhesive rags when none of spray paint gets inside them, because if it does then its parts are not working to the maxium capacity!
Step 4: Use steel wool to remove dirt or grease you have on your bike, even if you do not see any yet, do it anyway
Step 5: Use the sand paper and make sure its working right now painting is raw and boring! That's what you want! Make it look like it has a lot of scratches on it! That's what I want to play next step! (Be sure to get where they are welding, and the top tube and all that well, you want to go everywhere with sandpaper!)
Step 6: Get 2 metal clothes hangers, break them so its time a piece of metal, then bent so they make ends meet, then put a rack on the inside where you put the cloth on the inside of cloth in sterrior tube and put one of the racks of underwear from the bottom bracket. Finding a good sturdy tree branch (so that its structure does not fall out while your paint!) And hang your frame up on it!
Step 7: When part of a raw and ugly metal good color striped that can spray a light coat of primer on it, put your hand on the can of spray paint, use your index finger on the trigger of the paint and press down for a second half, and then with a "side by side" light strokes of aerosol motion in the frame (Hold can 6 inches from the picture when the spray so it does not happen if it's leaking too close!). Let dry for 1 hour and repeat again with little more than a bit of it.
(NOTE: Be sure to avoid the runs! If you run occur, wait for it to dry and then sand the area and put a light coat of primer on.)
(NOTE: Be sure to avoid running again! Running occur, wait for it to dry and then sand the area and put a light coat on him.)
I hope I have helped:)
1 - We need to copy the outline of the pattern on a layer of fabric. Copy the stars, twigs and the lyrics too. 
3 - After embroider have to make the sandwich. First tack a piece of wadding to have embroidered star. 
4 - Now placed on the back of the star doing very well match the ends. To do this you can use pins as shown above. Also pictured 
5 - remember to not sew the opening where to give back to the room. Sewing machine and finish well to start and finish sewing. 
6 - Trim the excess fabric leaving a 3 mm margin around the seam. In the opening leave a little more leeway. As always, the batting is cut flush with the seam. 
This 
is the star with wadding cut to flush couture and ready to "flip. 
7 - With the help of the back of a very fine crochet tips removed and filled. 
8 - Once filled we close the opening that we used to flip the piece with a hidden stitch. 
Another year, another meeting increasingly grown, facilities and amenities in this beautiful place with beautiful people live two wonderful days! 
1 - Copy the outline of the pattern on a layer of white felt. 
2 - cut out the shape leaving 3 mm margin and give you a machine stitched along the entire boundary of the circle. The stitch will be great (No. 4) and does not finish because the stitching is to frown. 
3 - impregnate the felt piece in water. 
4 - Then place the piece into a round mold. Tighten the felt against the mold and hold with a rubber band or tape. We leave the wick in the mold until it is completely dry. 
5 - When the wick is dry, remove from pan and keep us a bit of form. 
6 - We pulled one of the threads that have left no crinkle top and base of the circle. Fill with batting and then give a few stitches as shown in the photo to finish off the threads that have become loose to gather. 
7 - The hole in the base is not close at all because that anger hit the tail of the pineapple you will see in the picture below. 
8 - pinyon pine cones do not have the form shown in the photo. What we did was to peel the leaves from the top to make it the central trunk and to introduce air through the gap we have left to knit the piece of felt. 
9 - Before hitting the pineapple we do face. Using a marking pen water points will be located where the eyes, stitches in the mouth and nose. 
10 - will also have to cut the nose of a piece orange felt. The size of the nose is at home. 
11 - Here are the eyes sewn beads which are two large black and given stitches to his mouth. We used 4 ply yarn in taupe Mouliné DMC. 
12 - After we take a small cut and horizontal at the height of the nose. (See photo). 
13 - impregnate glue the base of the nose and the cut we made in the previous step. Enter your nose and let dry. 
14 - To end the face apply blush on both cheeks. 
15 - To place the pineapple at the base of the head of the snowman we opted for the hot glue gun. Apply a little silicone in the hole that has been at the base of the figure. 
16 - Enter the pineapple pressing a bit. Let dry. 
17 - The snowman wearing a scarf around his neck. To make it you have to cut a strip of 25 cm long and 1.5 cm wide, in red felt and make 4 cuts at the ends as shown in the photo. 
18 - This figure wears a black felt hat. To do this I refer to the "Snow Man's Face." 
NOTES: 
Note 1: For the star we are going to give a couple of ideas. The original figure is worked in a light yellow solid and this option has seemed nice. 
Note 2: Another little thing that we struggled to find. This is a golden ribbon brand Kreinik metallics 1 / 16 "ribbon No 002. The face of Santa Claus has a gold trim that frames and this tape is the one we used for this purpose. If you are fond of cross stitch to know better. 
Note 3: The beard of the figure is mohair wool specially treated to make wigs for dolls. 
Note 4: You will need a very small candy cane to decorate the Santa Claus beard. To do so follow the instructions on the entry "A Red Sock." 
1 - Copy the pattern of the star in two layers of fabric and make the sandwich with the batting at the bottom of the layers. 
2 - For the fabric does not move to sew sew a bit about the figure. Leave an opening in an arm of the star and remember to not sew that piece. 
3 - Once stitched and well finished off, trim the batting to the stitching and the excess fabric leaving 3mm. margin. Pickets shall be made for just where the picture indicates. 
quederá Thus doth the star from behind the batting cut to the stitching machine. 
4 - To finish it is filled and closed the opening with a hidden stitch. 
5 - Now we start with the face of Santa. Copy 
6 - We give back to the room and with the help of the back of a hook nose get very good. 
7 - Draw a straight line as shown in the photo. That line will sew and nose with volume. 
8 - After painting the line slightly fill the hole in the nose .... 
.. sew the machining with a very small stitch. Finish off the excess wire by hand. 
9 - Now we can put the border around the face and adjust it using a basting. 
10 - also can apply blush and eye make. The eyes are painted with black acrylic paint and a brush of triple zero. 
11 - We position the face in the center of the star. The pins and hold them and apply first-baste the entire upper arch ..... 
12 - Without cutting the thread, Meterman a bit of stuffing the hole has been left without sewing. In this way the face will have a bit of volume. We 
13 - This is the time to remove the water pen and prepare to implement the chin piece. 14 - sewing beard holding locks to the base with small stitches. 
15 - Here is the motif that we've done with Kreinik gold ribbon. 
16 - Eyebrows are also mohair. With this type of wool can be removed and sewing threads as we do with normal yarn or string. The eyebrows are two large stitches made with a lock of the wool. 
17 - With the needle wool is a hole passing through the upper arm of the star, there shall be put a ring. 
