READ WELL BEFORE.
MATERIAL USED FOR THE SKATER.
This is a list of all known materials and are almost always used:
This is a list of all known materials and are almost always used:
- Scissors, needle, pins, thread machine, thimble, stuffing, pearl ball DMC # 8 dark brown.
This is another list of tools.
- A white pencil, pen water, gold wire, a wire cutting curling iron, a curling head round brown acrylic paint, white glue, brush.
Fabrics:
- Solid color patch in meat, red felt, navy, black and bottle green.
This is another list of tools.
- A white pencil, pen water, gold wire, a wire cutting curling iron, a curling head round brown acrylic paint, white glue, brush.
Fabrics:
- Solid color patch in meat, red felt, navy, black and bottle green.
Note: the skater is 80% of the original.
BEGIN:
1 - With a soft pencil or pen to copy the outline of the water pattern on a layer of fabric. It copies only the outline. The opening to turn the piece is located across the base, remember that this part does not sew. Has no arms, therefore, no opening. We cut the pattern by the neck to give a little more range and do not pull the piece by that party to give back.
2 - then you must copy the outline and facial features in another layer of fabric. It is advisable to use a pen or pencil soft water. Spend very soft pencil. 
3 - Now are matched exactly, especially the part corresponding to the head and face, the outline that we have passed to a layer of fabric and contour to the features that we have drawn on another piece of cloth . With pins to make sure it does not move and put the padding back to the sandwich. 
4 - Before we can remove the pins to baste it is easier to sew the machining contour. We have placed the pickets to be given after cutting the outline right in the neck (see photo). 
5 - This figure will be cut after the contour along the lines of stitching, after removing the padding and margin to the pickets below the neck and around the head. 
6 - We looked the part, taking it all seams to the back of a hook and fill it starting slightly mind. We put very little filler and finally becoming close the opening with a stitching machine. Finish off well. 
7 - Now we start to paint the face. The brush is the triple zero, as always, and painting that we will use is a brown acrylic.
We painted the outlines of a pull and the following order: Pupil, upper eyelid, eyebrows, nose, mouth and freckles. When everything has dried it is water disappear pen. Lastly
apply blush.
We painted the outlines of a pull and the following order: Pupil, upper eyelid, eyebrows, nose, mouth and freckles. When everything has dried it is water disappear pen. Lastly
apply blush.
8 - Now we will make the pants, jacket and scarf. Pants passed the bottle green felt putting double layer using a light pencil. Machine-sewn with a small stitch along the line it has set. Finish well at the beginning and end of sewing. In the next picture is that parties have to sew and parties are also referred to the picket lines to do after cutting his pants.
9 - The same explanations apply to pants to the jacket. These two points are carried forward in reference to sew two buttons. The photo below shows the pickets and parts to be sewn. We have
a couple of changes to the original pattern: the opening to get his head is a little bigger than the original and have gotten a little stitching on both sides to attach by the jacket is over, but that, as always, Your choice.
a couple of changes to the original pattern: the opening to get his head is a little bigger than the original and have gotten a little stitching on both sides to attach by the jacket is over, but that, as always, Your choice.
A jacket you have to sew two buttons on the color you like. 
10 - We have prepared the cardboard soaked in fixing hair spray strong. When drying iron very well and with a white painting draws the outline of two boots and two gloves. We cut out the parts in the line very well have done. 
11 - The scarf the red felt cut off, 1.5 cm wide and long that you enjoy yourselves. Eventually cut the fringe. 
12 - dress the skater, we put the pants and attached to the body by stitching. 
13 - When we have finished sewing the pants at the waist, we put a bit of stuffing the pant legs. 
14 - Now we have to make the leaves of the skates. skates we used to wire is very ductile and easy cutting.
started with a simple loop at one end ...
... and we help of your thumb and forefinger to rotate the wire. With a spin and a half is enough ... 
... cut to length and finished with a small curve at the other end of the wire. 
15 - White-tailed impregnate the Boot tab. 
16 - We put the shoe between the flange and the boot and press with fingers to set the glue. We repeat this operation on the other boot. 
17 - to stick the boot to the pants glue is applied to both sides of the boot and on both sides of the pants, you enter the boot in the pants and pressed with fingers. Repeat the same procedure for the other leg. 
18 - To set the mouth glove-sleeve jacket repeats the operation done previously with the boot. 
19 - He tied the scarf and you're done. 
0 comments:
Post a Comment