Top Speed For Honda 400ex

A CHRISTMAS ANGEL.



READ WELL BEFORE.

MATERIAL USED FOR THE CHRISTMAS ANGEL.



This is a list of all known materials and are almost always used:

- Scissors, needle, pins, wires machine, thimble, stuffing, thread perlé # 8 dark brown skeins DMC mouliné dark brown and red.
This is another list of tools.
- A fine crochet, a marker of water, needle, wool, wire of 0.60 mm. a long thin screwdriver, a curling iron to cut wire, a round head curling, water-based paints in white, black and red, a red colored paint.
Fabrics:
- yellow or gold felt, felt toast and tile, solid white patch of rough or broken.

Note: We have reduced the Angel of Christmas, is 90% of the original.



BEGIN:

1 - Draw the outline of the pattern a layer of fabric, using the reverse of it. The opening is positioned below the phrase "Merry Christmas" out there will turn the piece and to position the legs of the doll. Also mark the place where the arms will be located.

2 - Now on another piece of cloth to trace the outline of the angel, his face and references for embroidery decorating the tree with his body.

3 - Now we have to match the two contours as in the photo. We make sure they match exactly the two points where the neck ends and subjected the two fabrics with pins, position is important fabrics.

4 - Now place the batting, as always, last and machine-sew, stitch slowly and small. You can string together to remove the pins and make it easier to machine sewing. We begin, as always, at the point where you start opening it and keep topping stitching all around to the point where the opening ends. Finish off again.

remember to NO SEWING bottom opening of the gaps we have left to enter the arms.

5 - Once machine-stitched trim the margin to padding, only the margin and give bites that you see in the picture around the head (convex zone) to avoid forming peaks and ends where the neck (hollow area) and the face begins to pull no seams once turned the piece.

6 - Copy the outline of a star of 2 cm from top to bottom in gold felt. To make it consistent impregnated felt strong hairspray and let dry one day, when dry cut the pencil line with no margin.

7 - The same for the wings, feet and hands. The felt is impregnated, in this case brick (for wings) and toast (for hands and feet) of hairspray, dried, ironed a bit and then cut along the pencil line with no margin.

8 - We put the arms in their respective openings and the basting to position them in place and not move to pass machining. The sew.

9 - now fill the figure slightly, position the legs, sew and sew by machine.

10 - leftover yarns we have finished by hand.

11 - began to embroider on the nose with a skein DMC in dark brown and using two strands of thread. The tree trunk is large and stitching wire branches are passed. Also are embroidered with French knots red balls, using 4 strands of DMC floss mouliné red.

12 - paint the eyes with the same brush that we used to the "Angel Face." Utililzada painting white acrylic.

13 - Paint a circle for a mouth with red acrylic paint.

14 - With a swab soaked in water make the marker disappear once the paint dries.

15 - Paint the pupil with black acrylic. No need to paint the upper eyelid, but the eyes are more expressive with it.

16 - Paint a white dot in the pupil. With a toothpick or a pin, maybe you still better than the brush.

17 - To make the ornament takes the back we have to do a simple loop in one end of the wire going to use.

18 - With the thumb and forefinger of his left hand to mold the wire looks like the photo. With two laps is enough. Cut wire to desired length.

19 - Finally we make a hole in one end of the star that we had reserved and introducirmos in the loop.

20 - We make two holes (centered) in the wings.

21 - sew on the back of the angel with a few stitches.

22 - Enter the ornament with the star on the wings. If not well try holding it down with white glue.

23 - Now the hair is tied with a hank of dark brown bead in the 5 points you see in the picture, and finally flush is painted with red paint.